Our company
Akrodyn is an owner-run engineering company from Zurich, specialising in servo controllers, embedded systems and firmware.
Management team
Our management team brings together years of experience in electronics development, embedded systems and industrial innovation. Trained to ETH MSc level in electrical engineering, robotics and mechanical engineering. You know who will work on your product before the project starts: you meet everyone involved in person.
Varin Buff
Head of System Architecture & Safety
The best solution seems obvious in the end.
Björn Joos
Head of Product Development
Dynamic and pragmatic: from creative visions to practical products.
Sebastian Tschabold
Head of Power Electronics & FOC
From schematic to firmware: I make sure electronics not only work, but impress. 10+ years developing servo drives and field-oriented control algorithms.
Specialised across six areas
Servo motor control
Field-oriented control with near-dead-beat behaviour and current loop rates up to 50 kHz. Sensorless operation down to 0 Hz including starting under load, MTPA for maximum torque per amp, and field weakening for high-speed ranges.
DC/AC inverters
Power stages built on IGBT, SiC, MOSFET and GaN topologies for industrial use. From device selection and gate driver design through switching loss and thermal optimisation to a robust commutation loop layout.
Brake choppers
Chopper solutions developed in-house up to 100 kW and 999 V, fully customised on request. Switching stage, braking resistor and cooling sized against the real duty cycle – including DC-link and energy management.
Safety
TÜV-certified drive safety to PL e and IEC 61508 SIL 3. Supported end to end: safety concept, FMEA and FMEDA, architecture and diagnostics, verification through to an approved, certified series product.
EMC
Compliance with EN 61800-3 C2/C3 is planned in from the start: filter design, layout, shielding and grounding concept, and pre-compliance measurements along the way – instead of expensive rework shortly before release.
Cybersecurity / CRA
Security by design to the Cyber Resilience Act and IEC 62443: threat analysis, secure boot, signed firmware updates, hardened interfaces, SBOM and vulnerability management across the entire product lifecycle.
Life at Akrodyn
Effective engineering, a richer life
Your idea, pragmatically built.
Solution-oriented & effective
We always think and act effectively and solution-oriented with the big picture in mind.
Quality
With good teamwork in all our partnerships, we reliably deliver the highest quality.
Trust
For us, cooperation is based on trust and honesty. Integrity means that we support each other.
Joyfulness
Joyfulness and independence accompany us in our work and are a key driver for the high quality of our results.
Creativity
We promote our creativity and innovative strength through continuous development and curiosity. This enables us to create the perfect solutions.
ÜGGU: four phases, clear outcomes
Structured problem-solving from the root of the problem: deliberated, discussed, debated, delivered. Rapid development without the overhead.
Deliberated
Carefully analyse requirements, define scope, check feasibility
Discussed
Goals, risks and trade-offs discussed openly and communicated clearly
Debated
The best solution fought out properly - no consensus for consensus's sake
Delivered
Documentation, production data and knowledge transfer
Dead-beat control and safety up to PLe
Our specialty is developing custom servo drives with a high current bandwidth of up to 6 kHz at a control frequency of 50 kHz - close to dead-beat control, since errors can be corrected in fewer than 3 control cycles. That results in a position bandwidth of up to 800 Hz.
Sensorless operation is possible down to a standstill of 0 Hz, which cuts cost, improves reliability and increases efficiency. Since our customers often work in safety-critical applications, we offer safety functions up to PLe.
- >Up to 80 kW motor power
- >12V to 999V input voltage
- >Up to 100,000 rpm with FOC
Together to the finished product, thanks to our partners.
We develop electronics, firmware and drives ourselves. Machining, industrial design, structural analysis and on-site assembly are handled by companies we work with closely. Coordination stays with us, so you have one point of contact for the whole product.
CNC precision machining from Altstätten SG: milling and turning from prototype to series, plus assembly and metrology. Including special materials such as MACOR glass ceramic.
Product development in Uster ZH, where industrial design, mechanics and optics meet. Developed to ISO 13485 where medical technology is involved.
Structural analysis and structural optimisation from Nänikon ZH, with certification experience from aerospace. They carry out our simulations and strength verifications.
Control cabinet building from Steinmaur ZH: and our fitter when a job needs hands in the field. His speciality is tanning salon technology.
Tell us what you have in mind.
An idea in your head? Or still unsure which technical route is the right one? Together we work out which architecture, which components and which timeline suit your plans, and what the next step looks like.
Online via video call or in person in Zurich
Request a sparring session